Wheel Hub Assembly For Bmw 5 6 7 31206850154

Wheel Hub Assembly For Bmw 5 6 7 31206850154

Wheel Hub Assembly For Bmw 5 6 7 31206850154 BMW 5 (F10) 2009/01-2016/10 BMW 5 Gran Turismo (F07) 2009/01-2017/02 BMW 5 Touring (F11) 2009/11- BMW 6 Convertible (F12) 2011/03- BMW 6 Coupe (F13) 2010/11- BMW 7 (F01, F02, F03, F04) 2008/02-2015/12 BMW X4 (F26) 2013/05-2018/03 BMW X3 (F25) 2010/09-...

Wheel Hub Assembly For Bmw 5 6 7 31206850154

 

BMW 5 (F10) 2009/01-2016/10

BMW 5 Gran Turismo (F07) 2009/01-2017/02

BMW 5 Touring (F11) 2009/11-

BMW 6 Convertible (F12) 2011/03-

BMW 6 Coupe (F13) 2010/11-

BMW 7 (F01, F02, F03, F04) 2008/02-2015/12

BMW X4 (F26) 2013/05-2018/03

BMW X3 (F25) 2010/09-

 

Tip 1. Use copper rods and manual hammering to install

This is an easy way to install small and medium-sized bearings. When the inner ring of the bearing is tightly fitted and the outer ring is loosely fitted, the copper rod is closely attached to the end surface of the inner ring of the bearing, and the copper rod is directly struck by the hammer, and the bearing is slowly applied to the shaft through the force transmission of the copper rod.

When the inner ring of the bearing is large, the copper rod can be evenly tapped around the end surface of the inner ring of the bearing. It is forbidden to hit only one side, and it should not be used too hard. It should be symmetrically tapped, gently tapped and slowly installed to avoid the oblique cracking bearing. .

Tip 2, using a sleeve to install

This method is the same as the use of a copper rod to mount the bearing. It presses the sleeve directly on the end face of the bearing (the end face of the inner ring is pressed when the bearing is mounted on the shaft; the end face of the outer ring is pressed when installed in the hole of the housing), and the tapping force of the hand hammer can be evenly distributed in the installation. The bearing is on the entire end face of the ferrule and can be used together with the press. The installation saves labor and time, and the quality is reliable. The sleeve used for installation should be made of soft metal (both copper or low carbon steel).

If the bearing is mounted on the shaft, the inner diameter of the sleeve should be slightly larger than the journal 1-4mm, the outer diameter is slightly smaller than the diameter of the inner ring of the bearing, or the thickness of the sleeve, the thickness should be equal to the thickness of the inner ring of the bearing. 2/3-4/5, and the ends of the sleeve should be flat and perpendicular to the barrel. If the bearing is installed in the seat hole, the outer diameter of the sleeve should be slightly smaller than the outer diameter of the bearing.

Tip 3, press indentation

The installation pressure should be applied directly to the end face of the bearing ring with interference fit, otherwise crushing will occur on the working surface of the bearing, resulting in rapid bearing damage.

Tip 4, heating installation

For the installation of bearings with large interference or large-size bearings, in order to facilitate the installation, the principle of thermal expansion and contraction can be used to heat the bearings in the fuel tank and then install them with copper rods, sleeves and hammers. The temperature during heating is generally controlled below 100 ° C, and 80-90 ° C is suitable.

When the temperature is too high, the bearing ring raceway and the rolling element are easily annealed, which affects the hardness and wear resistance, resulting in reduced bearing life and premature scrap.

Wheel Hub Assembly For Bmw 5 6 7 31206850154